!!! MİCROBOX II HAYIRLI OLSUN !!

Kapat
X
 
  • Filtre
  • Zaman
  • Gösterim
Clear All
yeni mesajlar
  • ELMADAÐLI
    Senior Member
    • 05-11-2004
    • 3194

    !!! MİCROBOX II HAYIRLI OLSUN !!


    New Dongle Microbox II

    11.08.2010

    Working on w3 & w6 & nss6

    Note: Not upload to Microbox I
  • ELMADAÐLI
    Senior Member
    • 05-11-2004
    • 3194

    #2
    Konu: !!! MİCROBOX II HAYIRLI OLSUN !!

    Step 1:

    - Connect the MicroBox dongle to the power, and make sure its turned on ( Red light inside it ), after that connect the serial port from the MicroBox to the serial port, in your PC.

    Step 2:
    - Download the cleaner software for the downloads section, then open the .rar file and you should be able to see the below files, open the cleaner.exe file.


    Step 3:
    - After you have the program opened click START button, then you should see that a "Waiting Boot..." is showing up near the software title, as the below image shows.


    Step 4:
    - Now unplug the power cable from the dongle for 2 seconds then plug it again, into the MicroBox, after that you should be able to see the progress bar increasing and the cleaning process is started, as the below image shows.


    Step 5:
    - Once the cleaning process reaches 100%, you are good so far, unplug it again from the power for 2 seconds then plug it again.

    Step 6:
    - Now download the software that you want to install from the site, then open the .rar file as below.


    Step 7:
    - Open the .exe file, which is the software it self.

    Step 8:
    - After you have the program opened click START button, then you should see that a "Waiting Boot..." is showing up near the software title, as the below image shows.

    Step 9:
    - Now unplug the power cable from the dongle for 2 seconds then plug it again, into the MicroBox, after that you should be able to see the progress bar increasing and the transferring process is started, as the below image shows.

    Step 10:
    - Once the transfering process reaches 100%, you are good so far, unplug it again from the power for 2 seconds then plug it again, and by this you have the software installed at your MicroBox Dongle.

    Hope this was useful for you.

    Regards,
    mana5olia


    --------------------------------------------------------------------------------

    How to Install MicroBox II Software:

    Step 1:

    - First of all if you have MicroBox I, you have to convert it to MicroBox II, so what you need to do is to download the Loader software form the softwares section, you will see the file as below:


    Step 2:
    - Now as you can see in the above picture, choose your configuration, like the port that you want to use, in our case its COM1, and the mode as well, download, Dump, Erase. In our case we want to download the file so we should choose download. After that click browse and locate the .bin file that you want to download, e.g download the W3 software and locate it from the downloader.


    Step 3:
    - Now click download and the downloading should start automatically, so depends on the software the you choose, you dongle will be updated upon that. Once you are done, reboot your dongle and you should be fine.

    Thanks,
    mana5olia






    şağıda MicroBox dongle güncelleştirme hakkında ayrıntılı adımlar vardır.
    Adım 1:
    MicroBox dongle için güç - Connect ve (yaptığınız açık onun emin içine ışık Kırmızı ), bundan sonra porta seri seri bağlamak MicroBox limanından, PC yapın.
    Adım 2:
    yazılım indirme bölümü temiz - İndir, sonra dosyayı açın. rar ve açık, dosyalar altında güçlü gerektiğini görmek cleaner.exe dosyası.

    Adım 3:
    size - sonra programı tıklayın açılan START butonuna, o zaman göreceksiniz ki bir "Bekleyen Boot ..." gösteren görüntüsünün altında yakınında gösteren up gibi yazılım başlığı.

    Adım 4:
    - Şimdi 2 saniye dongle gelen güç kablosunu fişten çekin sonra tekrar MicroBox içine, bundan sonra sen ilerleme çubuğu ve artan temizleme işlemi başlatılır, görüntü görüldüğü gibi aşağıya bakın gerekir takın.

    Adım 5:
    - Temizleme işlemi% 100 ulaştığında, iyi şimdiye kadar olan yine 2 saniye süreyle iktidardan sonra tekrar takın çekin.
    Adım 6:
    - Şimdi sitesinden yüklemek istediğiniz yazılımı sonra. Rar aşağıdaki dosyayı açmak indirin.

    Adım 7:
    - Yazılımı kendine. Exe dosyasını açın.
    Adım 8:
    size - sonra programı tıklayın açılan START butonuna, o zaman göreceksiniz ki bir "Bekleyen Boot ..." gösteren görüntüsünün altında yakınında gösteren up gibi yazılım başlığı.

    Adım 9:
    - Şimdi 2 saniye dongle gelen güç kablosunu fişten çekin sonra tekrar MicroBox içine, bundan sonra sen ilerleme çubuğu ve artan transfer süreci başladığında, görüntü görüldüğü gibi aşağıya bakın gerekir takın.

    Adım 10:
    - Aktarılması işlemi% 100 ulaştığında, iyi şimdiye kadar olan yine 2 saniye süreyle iktidardan sonra tekrar takın çıkarın ve yanında size yazılım MicroBox Dongle de yüklü bu.

    Umarım bu yararlı senin için oldu.

    Saygılarımızla,
    mana5olia

    Nasıl MicroBox II yazılımı yüklemek için:
    Adım 1:
    Eğer MicroBox ben varsa - Her şeyden önce, sen MicroBox II dönüştürmek gerekiyor, böylece ne yapmanız gereken Loader yazılım programları bölümünde formunu indirmek için, aşağıdaki gibi dosya göreceksiniz:

    Adım 2:
    - Şimdi siz yukarıdaki resimde görebilirsiniz senin yapılandırma seçtiğinizde, liman siz de, bizim durumumuzda olan COM1, ve modu kullanmak, Dökümü, Erase indirmek istediğiniz gibi. biz download seçmeliyim bizim durumumuzda bu dosyayı indirmek istiyorum. o tıklama taramak sonra. bin ki Yüklemek istediğiniz dosyayı bulmak, W3 yazılımını indirin ve downloader dan bulun örneğin.

    Adım 3:
    - Şimdi tıklayın indirmek ve indirme otomatik olarak başlamalı, bu nedenle siz seçtiğinizde, dongle yazılım üzerine, güncellenecektir bağlıdır. Bir kez bitmiş, sizin dongle yeniden ve iyi olmalıdır.

    Teşekkürler,
    mana5olia

    Yorum

    İşlem Yapılıyor
    X